Get in Touch with Mackayhairscissors Company
Factory-Direct · OEM / ODM · From 50 Pieces
Bulk Wholesale Scissors
Wholesale Hair Scissors — Japanese-Steel Hairdressing & Barber Shears, Factory-Direct from 50 Pieces
We forge our wholesale hair scissors using Japanese steel, and hand finish every single one of our high-quality blades so that our distributors, salon chains, and private-label brand owners can sell a truly professional edge at a fraction of the price a Western reseller would charge. Mackay is the factory – 440C, VG10 and ATS-314 shears hardened to 60-64 HRC and honed by hand to a convex edge, and shipped to buyers in over 40 countries.
- 440C–ATS-314Japanese steel grades
- 60–64 HRCVacuum + cryo tempered
- 50 / 1 pcMOQ custom / in-stock
- 80+ steps100% hand-honed convex
- 40+Export countries
- ISO 9001BSCI · SGS audited
Why professional buyers source hairdressing & barber shears factory-direct
Structurally, the reason is simple: because a vertically integrated factory controls the furnace and the honing, it can publish specs a reseller cannot — every blade engineered to a documented hardness. Unlike an opaque supplier, we show the trade-off up front, which is the mistake most buyers make when they pay for a brand story instead of a documented blade. Origin labeling follows U.S. country-of-origin guidance, so nothing about the sourcing is disguised.
wholesale buyers of hairdressing scissors invariably find themselves caught between two extremes. On the one hand, opaque Chinese manufacturers will quote you only after an extensive “$5,000 minimum” email exchange, and refuse to reveal their hardness or heat treatment steps – so there’s no way of verifying what you’re reselling until you open the carton. On the other hand, Western own-brand agencies sell Chinese-made shears marked up by several hundred percent, slap their own label on it, and prohibit you from putting yours. Neither works for a distributor, a salon chain or a brand owner responsible to their own customers.
We eliminate this conflict because we do it all, from raw Japanese steel through to the final, hand-honed shear. This vertical integration allows us to publicly disclose information that other suppliers conceal – like steel grade, Rockwell hardness, and edge geometry – and still sell at factory-direct prices. It also explains our “Japanese steel, Chinese craftsmanship” reality: we cut our blades from authentic Japanese steel (our ATS-314 plate comes direct from Hitachi in Japan), forge, heat-treat and hand-finish in our own factory – conforming to US country-of-origin labeling requirements – with zero obfuscation. In this regard, transparency is key to winning your business. An opaque RFQ factory hides the process; an own-brand reseller jacks up prices and prohibits branding. We provide transparent, honest, verifiable specifications with factory-direct pricing and no hidden trade-offs – a transparency most buyers overlook, opting for a story instead of a verified blade.
Sourcing options crosswalk
Below, the table lays out the decision many buyers actually make. It compares a factory-direct OEM (us) with the two other solutions available to the market for these hair scissors programs – highlighting how they impact your profit and defendability.
| Factor | Factory-Direct OEM (Mackay) | Opaque RFQ factory | Own-brand reseller | Premium branded shear |
|---|---|---|---|---|
| Starting MOQ | 1 pc stock / 50 pc custom | Often gated at $5,000+ | 10+ pcs, no custom | 1 pc, no wholesale |
| Published hardness | 60–64 HRC, per grade | None | Sometimes (59–61 HRC) | Rarely |
| Heat-treat disclosure | Vacuum + cryogenic, 80+ steps | None | None | None |
| Private-label / OEM | Full custom + laser engraving | Case-by-case | Not offered | Not offered |
| Reseller markup on you | Zero — factory price | Zero, but unverifiable | High | Highest |
It’s a familiar pattern: buyers aren’t losing money because of low Chinese costs; they are losing it due to a lack of verifiable specifications or branding control. Everything on this page is designed to resolve these issues for our customers.
Contact Us For Factory-Direct Pricing →
The Mackay hairdressing & barber shear range— types, steel and sizing
One catch with a thin catalog is hidden specs; because we engineer every model in-house, each carries a documented 60–61 HRC and a smooth, razor edge, unlike a reseller who can only quote a price. That gap is the mistake a hair thinning scissors or hair shears buyer cannot afford.
Buyer beware: what you thought was a supplier’s “catalog” is actually just three models in a rebranded disguise with a secret mark-up, and no data for size or hardness-the error that delays many hair cutting scissors programs from leaving the premises before delivery. The catalog that runs beneath the premium MATSUOPRO brand covers the full working bench of a salon or barbershop — hairdressing and barber hair cutting scissors, thinning shears for blending and weight removal, texturizing and trimming shears, and the pet-grooming shears that so many distributors bundle together into the same order. We design all of our shears ourselves in-house, so each model includes a detailed grade specification and a smooth hand-honed edge (60-61 HRC). You won’t find that from a re-seller who only knows a price. The full matrix of professional hair scissors, japanese hair scissors and thinning scissors means an engineer on your team can align a specific model to a specific haircut style or to a request without extensive back-and-forth. The decision matrix is designed so you don’t have to wade through Yes/No feature charts – each type of shear shows you the recommended uses, steels, sizes, hardness and minimum order for your high-quality wholesale choice.
Scroll to explore track
01 / PRIMARY
Hairdressing straight-cutting scissors
Steel:Japanese 440C / VG10
Size:5.5–7.0 in
Hardness:60–61 HRC
Edge:hand-honed convex
from$22.00/ pc
02 / BARBER
Steel:440C / 9Cr
Size:5.5–6.5 in
Hardness:58–61 HRC
Finish:matte/gold/mirror
Barber & texturizing shears
from$8.82/ pc
03 / BLEND
Thinning & blending shears
Steel:VG10 / 440C
Teeth:28–56
Size:5.5–6.5 in
Use:weight removal
from$24.90/ pc
04 / PET
Pet & dog grooming shears
Steel:VG10 / 440C
Size:7.0–7.5 in
Hardness:60–61 HRC
Detail:upper/lower bend
from$21.76/ pc
05 / FLAGSHIP
Damascus VG10 flagship
Steel:Damascus (VG10)
Size:7.0 in / 18 cm
Hardness:61 HRC
Finish:water-ripple
from$298.00/ pc
06 / PRO COBALT
Cobalt flagship line
Steel:cobalt alloy
Size:5.5–6.5 in
Hardness:up to 64 HRC
Use:longest edge life
Decision matrix — which shear for which account
Straight cutting
► Salon chains, distributors
Steel440C / VG10
Size (in)5.5–7.0
Hardness60–61 HRC
MOQ1 / 50
Barber / texturizing
► Barber supply, academies
Steel440C / 9Cr
Size (in)5.5–6.5
Hardness58–61 HRC
MOQ1 / 50
Thinning / blending
► Full-bench salon programs
SteelVG10 / 440C
Size (in)5.5–6.5 (28-56T)
Hardness60–61 HRC
MOQ1 / 50
Pet / dog grooming
► Grooming distributors
SteelVG10 / 440C
Size (in)7.0–7.5
Hardness60–61 HRC
MOQ1 / 50
Damascus flagship
► Retail hero / statement
SteelDamascus VG10
Size (in)7.0
Hardness61 HRC
MOQ1 / 50
Any model can be made to left hand, with your choice of a swivel thumb, an offset thumb (for improved ergonomic comfort), and any of the blade finishes. Blade size, blade geometry and the number of teeth are detailed on each spec sheet so you can match a model to your request without a costly exchange after delivery. Standard scissor geometry follows the industry’s most popular designs, including the hollow ground, convex edge that’s the subject of many early patent filings (e.g. US 3,374,694 A).
[ Inquiry Station ]
Ready to match models to your product line?
// Edge Retention Analysis
The steel and edge that win you repeat orders
As professionals put it, steel quality is the most important factor, and real Japanese made scissors hold their edge longer because of process, not marketing. If the seller can only tell you the steel type and nothing about the heat treatment, that is a red flag. Our honest version: genuine japanese stainless steel, verified before it ships, whereas a marked-up brand hides how the blade was treated. That convex geometry we hand-hone traces to documented cutlery patents such as US 5,781,999 A for thinning shears.
Here’s the most poorly kept secret in the business, and not always the factor the retail price represents: A properly heat treated 440C shear will outlast a poorly heat treated VG10; a $600 rebranded shear often cuts no better than a well heat treated $40 pair. Steel quality is what professionals call the single biggest factor separating good from bad; poorly manufactured steel quickly loses its sharpness. Even so, the type of steel is just a starting point. Here is the truth: The level of edge retention on any tool is determined by the heat treatment process and how it is sharpened – and this is where the opaque supplier world, which we are committed to transparency, can hide things. A dealer that cannot give you information beyond steel grade, you may want to avoid. Genuine Japanese made scissors, as any professional would attest, are known to stay sharp, maintain perfect balance, and are built to last, thanks to years of development, not flashy marketing.
“We settled on vacuum treatment plus a cryogenic soak because it is the only combination that let us hold 440C and VG10 at 60–61 HRC across a whole production batch without warping the thin blade. Any factory can quote a steel grade — holding the hardness uniformly, blade after blade, is the part that takes the furnace and the 80 steps.”— Mackay Engineering Team, R&D
Precision Verified
And that is our entire point. We publish the full chain: every blade is vacuum heat-treated and cryogenically tempered, which converts retained austenite to martensite and lets us hold a uniform 60–61 HRC across our 440C and VG10 lines and up to 64 HRC on the cobalt flagship. Every premium blade passes through 80+ individual steps, is CNC-cut for repeatable geometry, then hand-honed by our craftsmen to a Japanese convex edge and mirror polish.
A convex edge is the sharpest, smoothest geometry a shear can carry; it glides for slide and point cutting where a cheaper flat bevel catches and pushes the hair. Each Rockwell C figure we quote is confirmed on our own benches before a pair ships. We hold every blade to a Convex-Edge Verification Standard: each pair is checked by hand for a true convex geometry and a smooth, high-quality mirror finish, cut from genuine japanese stainless steel rather than softer Chinese-sourced stock.
// Material Index Reference
The Six-Steel Buyer-Fit Index
It is important that you are given not just the steel, but also the appropriate level of edge-care it requires, based on its Rockwell C value and edge behavior. It lets you set up a good/better/best hierarchy.
| Steel grade | Hardness | Edge retention | Corrosion | Resharpen | Cost tier | Best for |
|---|---|---|---|---|---|---|
| 9Cr (entry) | 56–58 HRC | Moderate | Good | Easy | $ | Training / back-bar / budget lines |
| Japanese 440C | 60–61 HRC | Good | Very good | Easy | $$ | Everyday salon & barber workhorses |
| VG10 | 60–62 HRC | High | Very good | Moderate | $$$ | Premium daily drivers, slide cutting |
| ATS-314 (Hitachi) | 60–62 HRC | High | Very good | Moderate | $$$ | Premium lines needing toughness |
| Cobalt alloy | up to 64 HRC | Highest | Good | Harder | $$$$ | High-volume pros, longest edge life |
| Damascus (VG10 core) | 61 HRC | High | Very good | Moderate | $$$$ | Retail hero / brand statement pieces |
Why cryogenic tempering matters for a thin blade
Cryogenic treatment after hardening converts retained austenite to martensite, which raises attainable hardness and edge stability. On a thin, precision-ground hair blade, that gives a longer-lasting edge holding through more haircuts before re-sharpening — the difference between a stylist honing monthly versus bi-weekly.
Request a spec sheet & free sample →OEM / ODM & private label — your brand, our factory
Most “custom” programs make the same mistake: they stop at the sticker. Because we cut at the level of the steel, an OEM buyer gets a documented spec, unlike a logo-on-stock reseller — the reason our 50-piece minimum still ships a verifiable blade. For buyers registering their own mark, we support the USPTO trademark process with the documentation you need.
“Brand owners and distributors want custom scissors with an OEM program — and often their biggest concern is that ‘custom’ merely means a label on a standard pair, that the minimum is unattainable, or that the factory will pass off lesser-quality shears than those that were shown in the sample. Our OEM program alleviates all of those concerns. Since we have in-house control over our entire process-from melting to finishing-we can customize everything from the steel grade (from 9Cr to cobalt), to handle style (offset, crane or swivel), to color, custom laser etching for the logo, and retail-ready packaging, to your specific requirements.
For the full breakdown of custom steel, handle and engraving options, see our dedicated custom hair scissors & logo-engraving service. Unlike many ‘custom’ brands who simply place a sticker, we let you custom-build every pair at the steel level, and our 50-piece minimum can be verified on a physical sample.
OEM Readiness Checklist
- Steel grade selection for the price point and cutting edge quality tier (see Steel Selection Chart)
- Handle shape-crane, offset, or swivel-and split by handedness
- Vector graphic supplied for laser engraving, blade or tang placement decided upon
- Finishing and packaging: matt, high polish, PVD color or gold, presentation case, pouch or box
- Physical pre-production sample signed off before a 50-unit batch begins
Wholesale pricing, MOQ, margins and lead time — transparent from the first order
Supply Chain Cost Analysis
Factory
Direct
Direct
Private Label
Reseller
Reseller
Salon Retail
Price
Price
Capture the Hidden Markup spread.
Distributors lose margin not to unit price but to hidden reseller layers; because we quote factory-direct, you keep the spread, unlike an own-brand buy where the markup is baked in. Structurally the trade-off is stated, not hidden — no middle layer between the furnace and your invoice.
When buying, what worries distributors is not so much unit price as margin and unexpected charges. You get the price breakdown a wholesale buyer needs, with the factory price and no added margins. With our Factory-Direct vs Reseller Cost Ladder, you know precisely how margin is distributed unlike a private-label seller that adds a markup between the mill and your delivery.
Our range runs from $8.82 for a 9Cr barber pair to $298–368 for the Damascus VG10 flagship, while everyday 440C and VG10 salon shears land around $22–29 — a true quality ladder to build a wholesale line on. By buying factory-direct, you capture the full margin.
0%+
typical gross margin on professional shears resold through the salon channel — captured, not shared with a reseller, when you buy factory-direct.
Salon retail-vs-service margin benchmark (industry data). Your landed cost and margin depend on grade, volume and destination — request a quotation.
What drives your quoted price
Four factors influence a wholesale price: steel type(9Cr-steel to Cobalt-steel), volume in the range, extent of customization (from basic finishing to custom packaging and branding) and export logistics to one of over 40 destinations worldwide. We share the list of influencing factors instead of one overall price, and we always include a delivery time frame with our quotation. If you import products in large quantities, check the United States International Trade Administration for detailed customs information for your country.
Want your landed cost by volume and grade? Request a wholesale quotation →Quality you can verify — certifications, testing, QC and factory scale
“Certified.” It’s the one word buyers in this sector demand and one they have been trained to mistrust. In fact, the most famous premium brand in the industry was exposed for supplying Chinese-made shears while “implying more.” We are direct: “Certified” to us means verifiable documentation, not puffery. Our manufacturing is audited to BSCI and SGS standards, and runs on an ISO 9001 quality system; we are partnered with a national-level tools-and-hardware quality inspection center; and third-party hardness and material reports are available on request — no “contact us for the certificate” gatekeeping. Every single pair is individually inspected for sharpness, balance, tension, and finish before shipping. As opposed to the “contact us” type of supplier, we put documentation in the hand of a distributor or salon chain compliance officer as requested – precisely what an OEM buyer needs for a 5.5-7.0 in professional hair scissors program shipping to 40+ countries.
01
ISO 9001
Quality management system
02
BSCI
Social compliance audit
03
SGS
Third-party inspection
04
Reports on request
Hardness & material
Need documentation for your compliance file? Request certificates & test reports
→
We back it up with a real, auditable factory: a vertically integrated plant of 2,000+ m2 with a team of 100+, operating its own CNC machining, vacuum and cryogenic heat-treatment furnaces, precision grinding lines, PVD coating, laser engraving and hand-honing stations. No critical operation is outsourced, which allows us to control quality and lead times in-house – and allows a wholesale buyer to get a straight answer when requesting an inspection or sample. The ISO 9001 system adheres to the internationally recognized ISO 9001 quality-management standard.
Professional Bulk Scissors Configuration Tools
FAQ
Support
FAQ
What is the minimum order for wholesale hair scissors?
Our in-stock styles ship in one piece so you can test drive the steel and edge yourself before committing. Custom and OEM orders start at 50 pieces – low, so growing brands and smaller distributors can offer their own private-label lines without five-figure buy-ins.
Can you private-label or OEM to my brand?
Yes. OEM/ODM is a core part of our business: your choice of steel, handle material, finish, color, engraved logo and packaging – approved against your pre-production sample prior to batch run.
Are these really Japanese steel if they are made in China?
We’re upfront: the steel is genuine, high-quality Japanese material (440C, VG10, ATS-314; with our ATS-314 sourced direct from Hitachi in Japan) and the blades are ground and hand-honed in our own factory in China. Barbers and stylists are coming around to the value of Chinese-made shears as long as the steel can be verified and the specifications published; what they are reacting to is Western marketing hiding unverified steel at a markup.
What hardness (HRC) are your blades, and why does it matter?
Our 440C and VG10 blades register at 60-61 HRC and the cobalt-alloyed line goes up to 64 HRC. This hardness, which comes from heat-treatment (not simply the name of the steel), is what determines how long the edge will hold up before a stylist starts feeling drag. We state it so you know what to expect.
What is a convex edge, and how is it different from a bevel edge?
A convex edge is hollow-ground for the smoothest possible sharpness, which enables clean slide-cutting and precise point cutting. A flat bevel edge, while cheaper to manufacture, has a tendency to catch and fold the hair on its facet. All premium Mackay blade shears are hand-honed to a convex edge.
What is the lead time on a wholesale or custom order?
Lead time will depend on grade, volume and custom degree – but you will get written, fixed lead times in every quotation, not ranges. In-stock styles go fastest; custom OEM runs start after your pre-production sample is approved.
Do you offer thinning, texturizing, left-handed and pet-grooming shears?
Yes. The catalog covers straight-cutting, thinning and texturizing shears (28-56 teeth), barber shears, and straight and curved pet/dog grooming shears – any model can be made left-handed or with a swivel thumb.
Which hair scissors can you supply wholesale and OEM?
As a wholesale hair scissors manufacturer, we supply the full professional range for haircutting professionals: professional hair cutting shears, professional hair cutting scissors, professional hairdressing scissors, hairdressing shears and professional hair shears, plus japanese steel hair scissors, hair thinning scissors and barber scissors japanese steel. Built for hairdressers and hairstylists who cut hair all day, each pair combines precision cutting with an ergonomic design and the quality scissors professionals expect — great quality held across the whole batch. Custom hair scissors, professional hair styling shears and full private-label lines round out the range. Buyers searching hair scissors manufacturer usa, japanese steel hair scissors wholesale or hair cutting shears professional order from the same documented catalog of professional hair scissors.
Can I get third-party test reports before I buy?
Yes, third-party hardness and material reports can be supplied. BSCI, ISO 9001 and SGS certifications are all documented.
